Request A Quote

Just about everyone has got their own thinking with regards to Installing A Bathtub.

Mounting a bathtub isn't specifically brain surgery, yet it does need strong plumbing, carpentry, and also often, tiling abilities. Replacing an old bathtub with a brand-new one is also a reasonably challenging job. If the old bathtub is easily accessible, the job can move immediately; if you have to open up a wall to get rid of the old tub and also position the brand-new bathtub, the job is a lot harder. In either case, the job is within a home handyman's abilities, although you will certainly need an assistant to move out the old bathtub and embeded in the brand-new one. Make sure you have certified yourself for the work and are comfortable trying it. Instead of working with a professional to take over a halfway-completed task, it is better to think about using one before you begin. Possibilities are you may require a professional plumber to make tube links.
This article will certainly aid you set up a brand-new bath tub in your restroom if you have actually already gotten a new bathtub and also don't require to change the plan of your previous water supply pipelines.
Your devices and also material list should make up the following:

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipeline Caps


 

Getting ready for the Installment

Firstly, the supporting framework provided with the bathroom must be fitted (if called for) according to the producer's guidelines. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is important to ensure that if the tap features a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps device to stop strain on the tub.
Fit the versatile faucet adapters to the bottom of both faucets making use of 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final position.

Removing Old Taps

If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you need to do is separate the water supply. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly problematic due to the restricted accessibility that is often the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a cloth all set for the continuing to be water that will certainly originate from the pipes. Once the supply pipes have actually been gotten rid of, utilize the same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming throughout this process. Once the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any old sealing compound.
Prior to carrying on to fit the new taps, contrast the pipeline connections on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.

Installing the Bath tub

Using both wood boards under its feet, place the bathtub in the called for setting. The wooden boards are handy in uniformly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four small factors.
The next objective is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the spirit level and also changing the feet on the bath tub up until the spirit level checks out degree.
To set up taps, fit all-time low of the furthest adaptable tap adapter to the proper supply pipeline by making a compression join; then do the very same for the other tap.
Activate the water system and inspect all joints and brand-new pipework for leakages and tighten them if essential. Fill up the bath tub and likewise examine the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, deal with the bath paneling as explained in the supplier's user's manual. Tiling as well as sealing around the tub should wait till the tub has actually been utilized at the very least once as this will certainly settle it right into its final setting.

Fitting New Taps

If the tails of the brand-new taps are plastic, then you will require a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a connection to the current supply pipes.
If you require to fit a monobloc, after that you will need lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, position the tap in the installing opening in the bath/basin guaranteeing that the washing machines remain in place in between the faucet as well as the sink. Safeguard the tap in position with the manufacturer offered backnut. When the faucet is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical faucet adapters. The former type must be attached to the faucet finishes initially, tightening only by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.

Tiling Around the Bathtub

In the area where the bath meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to break a stiff seal, triggering the water to pass through the wall surface in between the bathroom as well as the tiling, causing difficulties with wetness and possible leaks to the ceiling below.
You can choose from a range of coloured sealants to blend in your fixtures as well as fittings. They are sold in tubes as well as cartridges, as well as can securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to constantly fill the bathtub with water before sealing, to enable the motion experienced when the bathtub remains in usage. The sealer can fracture rather very early if you do not take into account this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the marketplace. It is suggested to fit the ceramic tiles utilizing water-resistant or water resistant adhesive and grout.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

 

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

 

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

 

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

 

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

 

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

 

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

 

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

 

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

 

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

 

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

 

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

We had been shown that report on Installing A Bathtub from an acquaintance on another blog. Sharing is good. One never knows, you may very well be helping someone out. Thank-you for taking the time to read it.

Make An Appointment